ARAV RX logo
JAEN
Recommended

RX Standard

The workhorse that combines worker safety and labor saving

Precise joystick control from a safe location up to approx. 1,000 km away over a 4G LTE/5G cloud connection. Multi-camera video (GMSL, dome and PTZ) without blind spots, combined with automatic hopper feeding, keeps people out of hazardous areas while maintaining productivity. The most balanced package, suited to sites from erosion-control dam works to disaster recovery.

Standard
Standard sub 1

Teleoperation and autonomy in one machine

Joystick operation from a safe area plus automatic hopper feeding. The most balanced configuration for keeping people out of hazardous areas while maintaining productivity, ready for a wide range of sites.

Operate from a safe area over the cloud

A cloud connection over the machine's 4G LTE/5G link provides stable remote operation from a safe location up to approx. 1,000 km away.

Precise joystick control

Joysticks, which allow finer control than a game controller, come as standard. Suited to precision work such as slope finishing and loading.

Multi-camera, no blind spots

An in-cab camera, a front dome camera and an overhead PTZ camera. Switching between the three viewpoints shows everything around the machine.

Automatic hopper feeding

Automates feeding into hoppers and crushers, freeing people from monotonous repetitive work and substantially increasing daily throughput.

Remote operation
from up to 1,000 km away

Ultra-low-latency transmission lets operators far from the site work as if they were sitting in the cab.

Latency
approx. 0.06 sec
Range
approx. 1,000 km

* Reference values measured in ARAV's test environment (recommended network, low load). Actual values vary with the network type, signal conditions and site load.

LiDAR-based autonomy
for repetitive work

The retrofit autonomous system takes over repetitive tasks such as hopper feeding and dump truck loading. LiDAR scans the dig area, so the machine keeps finding material in the pile. It helps with labor shortages and keeps people out of the machine's working area.

Tasks
Feeding / Loading
Cycle time
approx. 30 sec

* Reference value from ARAV's test site (0.7 m³ bucket class, feeding task). Actual values vary with the machine, site conditions and settings.

Automatic hopper feeding and screening

Autonomy

Automatic hopper feeding and screening

Automates feeding soil and rock into hoppers and crushers. After the dig area and the hopper position are registered, the machine repeats the dig, swing, dump and return cycle on its own. The operator becomes a supervisor who monitors the autonomous work and steps in manually only when something is wrong. Daily throughput rises substantially compared with manual work while the operator's workload goes down. It can be used for river dredging and screening, primary crusher feeding at quarries, concrete rubble screening, soil stabilization hoppers and more.

  • Automatic dig, swing, dump and return cycle
  • River dredging with screening
  • Quarry primary crusher feeding
  • Self-propelled soil stabilization hoppers
GMSL, dome and PTZ multi-view

Cameras

GMSL, dome and PTZ multi-view

An in-cab GMSL camera (720p/30fps, 0.3 s latency) is combined with a front dome camera (720p/30fps, 0.6 s) and an overhead PTZ cloud camera (1080p/30fps, 0.6 s). The low-latency GMSL feed shows fine movements at the bucket tip, while the dome and PTZ cameras give a wide view of the whole site. All three views are shown at once, so the operator works without blind spots.

  • In-cab GMSL camera (720p/30fps, 0.3 s latency)
  • Front dome camera (720p/30fps, 0.6 s latency)
  • Overhead PTZ camera (1080p/30fps, 0.6 s latency)
  • Three views on screen at once

* Video latency and resolution are reference values measured in ARAV's test environment (recommended network, low load). They vary with the network type, signal conditions and site load. Stable three-view display assumes the recommended device and bandwidth.

Intuitive control with a game controller

Controls

Intuitive control with a game controller

The excavator can be operated with an off-the-shelf game controller, so no special hardware is needed. The button and stick layout is quick to learn, and operators new to remote work can be productive within a short time. Control latency is approx. 0.06 s, so there is practically no perceptible lag. The operator watches the video on a tablet while operating.

  • Works with off-the-shelf game controllers
  • Short learning curve, no special training
  • Control latency approx. 0.06 s
  • Video monitoring on a tablet

* Control latency is a reference value measured in ARAV's test environment (recommended network, low load). Supported controller models and the time operators need to become proficient depend on their experience and site conditions. Please ask us for details.

Tablet-only operation

Controls

Tablet-only operation

In autonomous mode, the machine is run entirely from one tablet. Video monitoring, starting and stopping autonomous work, and adjusting parameters are all done by touch, with no controller or joystick required. The minimal setup makes deployment and operator training simpler.

  • Everything on one tablet
  • No additional controller required
  • Designed for supervising autonomous work
  • Minimal equipment to deploy
Precise control with joysticks

Controls

Precise control with joysticks

Joysticks optimized for construction machinery come as standard. Lever stroke and resistance are close to the real machine, allowing fine adjustments. Even precision work such as slope finishing or working close to structures can be done without strain, operator fatigue is reduced during long shifts, and you can switch to a game controller depending on the task.

  • Joysticks built for construction machinery
  • Lever feel close to the real machine
  • Suited to precision work such as slope finishing
  • Switch between joystick and game controller as needed
Cloud connection (up to approx. 1,000 km)

Connectivity

Cloud connection (up to approx. 1,000 km)

A cloud connection over the machine's 4G LTE/5G link allows remote operation from up to approx. 1,000 km away. There is no need to set up a cabin near the machine; work can be done from a safe office. A fail-safe brings the machine to a safe stop if communication is lost.

  • Cloud connection
  • 4G LTE / 5G required at the machine
  • Remote operation from up to approx. 1,000 km
  • Fail-safe stop on loss of communication

System components

  • Industrial PC: runs the autonomous-operation control software
  • LiDAR: 3D sensing of the surroundings
  • IMU: measures attitude and acceleration
  • Encoder: measures the swing angle
RX system components

SAFETY SYSTEM

Two independent stop systems

Remote and autonomous operation need safety mechanisms that react immediately to lost communication or anything unexpected. The RX series has two independent stop systems so the machine can always be brought to a stop.

Radio emergency stop

A dedicated radio link, separate from Wi-Fi and LTE

The site supervisor carries a handheld emergency stop unit that sends the stop signal over a dedicated low-power radio link. The handheld unit is used within line of sight of the machine. Because it is completely independent of Wi-Fi, LTE and other networks, the emergency stop works even when the network fails.

0.15s*

Response time to stop

Two-way

Communication

  • Independent of the network — works during network outages
  • Hydraulic lock can be engaged from the handheld unit
  • Automatic stop if the machine leaves the handheld unit's range
  • The handheld unit must be kept within line of sight of the machine

In Japan, the unit uses the 429 MHz / 920 MHz specified low-power radio bands. Radio regulations differ by country, so please ask us about use in your country.

Automatic stop on network faults

Communication between devices is monitored continuously

The link between the operator's device and the machine is monitored in real time. If the system detects rising latency, packet loss or other faults, it brings the machine to a safe stop automatically, before the operator even notices.

2s*

From fault detection to stop decision

Always on

Monitoring

  • Stop thresholds can be customized
  • Secure communication with authenticated, encrypted MQTT
  • Mesh Wi-Fi plus fiber, Starlink or 5G

Status visible on site

The machine carries a beacon light (red, yellow, green) that shows workers nearby whether it is running autonomously, on standby or stopped because of a fault. IP radios are used for voice communication on site, so the site supervisor and the person managing autonomous operation can talk at all times.

* Response and fault-detection times are reference values from ARAV's test environment and vary with the network, site load and settings. Operating the RX series requires the customer to ensure site safety, including work zoning, supervision and emergency stop arrangements. See the Safety page for details.

Use cases

Where this package is typically used

* The sites shown are typical examples of how the RX series is used. Each deployment is decided with the customer after reviewing site conditions, tasks and the safety management setup, on the premise that the customer is responsible for site safety.

Surplus soil yard
TeleoperationOwn yard

Surplus soil yard

Remote operation at a surplus soil yard on your own premises, combined with automatic hopper feeding for efficient work.

Disaster recovery
TeleoperationWorker safety

Disaster recovery

Clearing landslides after earthquakes or heavy rain. Recovery work proceeds quickly while workers stay out of areas at risk of secondary collapse.

Erosion-control dam works
TeleoperationUnmanned construction

Erosion-control dam works

Building check dams in mountain streams exposed to debris flows. Nobody is stationed in the hazard zone; the excavator is operated remotely from a safe area.

River dredging with screening
Automatic feedingLabor saving

River dredging with screening

Excavating river sediment and feeding it into a screening plant for grading. Combined with automatic hopper feeding, a small crew can keep the plant running continuously.

Quarry primary crusher feeding
Automatic feedingLabor saving

Quarry primary crusher feeding

Feeding raw rock into the primary crusher at an aggregate quarry. Automating this heavy, hazardous task keeps the crusher fed steadily with fewer people.

Concrete rubble screening
Automatic feedingDusty environments

Concrete rubble screening

Screening crushed concrete. The operator stays in a safe place away from the dust while automatic feeding keeps throughput stable.

Soil stabilization plant
Automatic feedingContinuous operation

Soil stabilization plant

Feeding the hopper of a self-propelled soil stabilization (mixing) plant. The automatic cycle holds a steady feed rate with a small crew.

Features by package

Compare RX Standard with the other packages

FeatureRX Entry Type R RX Entry Type A RX Standard RX Pro 
Teleoperation: typical sites
Surplus soil yards
Disaster recovery works-
Erosion-control (sabo) dam works-
Tunnel construction---
Dam construction---
Controls (latency approx. 0.06 s)
Tablet
Game controller-
Joystick-
Operator station---
Cameras
In-cab GMSL camera (720p/30fps, 0.3 s)-
Front dome camera (720p/30fps, 0.6 s)
Overhead PTZ cloud camera (1080p/30fps, 0.6 s)-
Site requirements
4G LTE / 5G coverage at the machine-
Clear line of sight between machine and relay (approx. 20 m)---
Site cabin to serve as the base station---
Fiber or satellite link at the base station---
Machine control (ICT)
2D/3D machine guidance (MG)--*1*1
2D/3D machine control (MC)---*1
Safety for autonomous operation
Virtual wall-*1*1*1
Automatic lever-pattern recognition-*1*1*1
Real-time obstacle detection with LiDAR--*1*1
Connectivity and range
Cloud connection (up to approx. 1,000 km)
On-premises connection (closed network)---
Automatic feeding: typical sites
River dredging with screening-
Quarry primary crusher feeding-
Concrete rubble screening-
Soil stabilization (self-propelled mixer hopper)-
Automatic loading: targets
On-site crawler carriers--*1*1
On-site dump trucks--*1*1
Road-going dump trucks--*1*1
Automatic excavation from BIM/CIM design data
Standard bucket---*2
Tiltrotator---*2
OPERA integration
UDP / CAN API---*2

*1 Planned for 2026

*2 Planned for 2027

* This list may change without notice as development progresses and product specifications are revised.

How a deployment works

01
Requirements and detailed consultation

We review your site conditions, existing machines, communication environment and operating setup, then agree on the equipment specification, installation scope and the schedule to start of operation. If needed, we run a demonstration on a test machine. Depending on the conditions, demonstrations may be charged separately.

2-4 weeks / online and on site
02
Installing the remote/autonomous system (hardware)

The system is installed at ARAV's assembly workshop or on site. It is a retrofit that does not touch the hydraulic system, so the machine can be returned to its original state. An in-house inspection checks the sensors, communication and safety functions.

1-2 weeks / workshop or on site
03
Equipment purchase and software agreements

After installation, we sign a purchase agreement for the equipment (remote-operation or automation unit) and a subscription agreement (monthly or annual) for the remote/autonomous operation application. Price, payment terms and maintenance scope follow what was agreed in the consultation.

Equipment: purchase / Software: subscription (monthly or annual)
04
Go-live and periodic maintenance

The equipped machine is delivered and operation begins. The first year includes periodic maintenance support and operator training. Maintenance from the second year is agreed based on the operating record. After reviewing operating conditions and the site setup, we may not be able to accept every project.

First-year support included / from year 2 by agreement

These steps describe how projects run in Japan. For sites outside Japan, installation, operator training and maintenance arrangements are discussed with each customer before the project starts.

Considering RX Standard?

Tell us about your machines and site, and we will get back to you by email.

Compare the other packages

Download the ARAV overview (PDF)

Evaluating ARAV RX for your site?

Contact us

Already using ARAV RX?

Contact us

Interested in becoming a distributor?

Partner program